ESD Static Resin Flooring System CONDUCTIVE. SAFE. DURABLE.
A multi-layer, electrically conductive epoxy resin flooring system engineered to dissipate electrostatic discharge. Specified for electronics manufacturing, cleanrooms, pharmaceutical facilities, munitions storage, and any environment where static electricity poses a risk to personnel, product, or process.
System Thickness
1.5–2
mm total build
Floor Resistance (RGP)
<10⁹ Ω
IEC 61340-4-1
Shore Hardness
80–85D
hard epoxy surface
Fire Rating
Bfl-s1
EN 13501-1
What is ESD static resin flooring?
The Arturo ESD Static Resin Floor is a 2-component, epoxy-based self-smoothing floor system with integrated electrical conductivity. Applied at 1.5–2mm total build-up, it provides a hard-wearing, seamless surface that actively dissipates electrostatic charge to ground via a copper tape earthing grid embedded beneath the conductive primer layer.
Unlike standard resin floors, the ESD system incorporates a dedicated conductive primer (EP6400) that forms a continuous, low-resistance electrical path through the floor to the earth point. This is critical in environments where an uncontrolled electrostatic discharge event could ignite flammable vapours, damage sensitive electronic components, or trigger explosive materials.
The seamless surface prevents the accumulation of particulates, bacteria, and contaminants, making it fully compatible with GMP, cleanroom, and pharmaceutical manufacturing standards.
Substrate & installation requirements
ESD systems are critically dependent on correct substrate preparation and earthing continuity. The following conditions must be verified before installation.
- Substrate compressive strength minimum 25 N/mm², confirm by pull-off test before proceeding
- Surface regularity SR2, grind high spots; fill cracks, blowholes and voids prior to priming
- Relative humidity below 75% RH, specify EP6700 2-Coat DPM or EP6960 1-Coat DPM if exceeded
- Copper tape earthing grid installed on substrate and connected to a verified earth point before EP6400 application
- Ambient and substrate temperature between 10°C–25°C throughout application and curing
- Post-installation resistance testing (Rgp) to IEC 61340-4-1 required to validate system performance
ESD Resin Floor Build Up
- Self-smoothing Floor
- Arturo EP2480
- Arturo EP2490
- Conductive Primer
- Arturo EP6400
- Copper tape
- Primer*/Scratch Coat
- Arturo EP6600
- Arturo EP6200
- Subfloor
Product information
Arturo EP2480
Arturo EP2480 is an electrically conducting, ca. 1.5 mm thick, epoxy-based floor finish.
Arturo EP2490
Arturo EP2490 Self-smoothing Floor is an electrically conducting, coloured, epoxy-based floor finish for indoor areas.
Arturo EP6400
Arturo EP6400 electrically conducting primer is a waterborne, 2-component, electrically conducting, epoxy-based primer.
Arturo EP6600
Arturo EP6600 Primer is a 2-component, epoxy based primer. Also universally applicable as a scratch coat (2-C, EP)
Arturo EP6200
Arturo EP6200 Scratch Coat is a light coloured, 2-component, epoxy-based scratch coat.
*Or Arturo EP6700 2-Coat DPM or Arturo EP6960 1-Coat DPM if required.
Technical Properties
|
FeRFA Classification Type 5 |
Total System Thickness 1.5 mm – 2 mm |
|
Shore D Hardness 80–85 (hard epoxy) |
Abrasion Resistance ≤ AR0.5 |
|
Chemical Resistance Good* |
Fire Classification B fl-s1 (EN 13501-1) |
|
Floor Resistance (Rgp) < 10⁹ Ω |
Electrical Test Standard IEC 61340-4-1 |
|
Underfloor Heating Compatible |
UV Stability No - interior use only |
|
Usage Classification Medium duty |
Slip Resistance Option available on request |
| Curing times at 20°C / 65% RH | ||
| 16 hours Ready for foot traffic. Electrical resistance testing may proceed after this point. | 3 days Full mechanical resilience achieved. Equipment and racking may be repositioned. | 7 days Full chemical resistance. Normal operational use, cleaning regime, and ESD footwear testing can begin. |
Performance Benefits
Electrostatic discharge control
Dissipates static charge continuously to earth, protecting sensitive electronics, explosive materials, and personnel from ESD events.
Explosion protection
Prevents ignition of flammable vapours and explosive materials by eliminating static spark risk, critical in munitions, solvent-handling, and ATEX zones
Impermeable seamless surface
Jointless finish with no seams or grout lines. Impermeable to liquids and process chemicals. Compatible with GMP and ISO cleanroom cleaning regimes.
Chemical resistance
Epoxy chemistry provides good resistance to a wide range of process chemicals, cleaning agents, and solvents. Full chemical resistance list available on request
22 RAL colour options
Available in 22 RAL colours via EP2490, allowing zone demarcation, hazard coding, or design differentiation without compromising ESD performance.
Impact and wear resistance
Shore D 80–85 epoxy surface handles medium-duty industrial foot traffic, trolley movement, and light equipment use without compromising conductivity.
NBS Source
Request a system data sheet or technical consultation
Arturo technical team +44 (0)1788 530 080 | arturo.uk@uzin-utz.com
